Plan a temporary dish installation for a one-day event broadcast

A one-day event broadcast often needs satellite capacity for a contribution feed, remote interview or multi-camera production. A temporary dish can go on a roof, forecourt or hill, but a correct map pin does not replace a physical sky-view check. SatPointer supplies the pointing calculation; the crew must verify access, clearance and safety.

Begin with the broadcast chain. A receiving dish points toward a satellite carrying a live feed; an uplink dish sends the event back to a broadcaster or contribution network. A downlink may deliver a remote feed to the venue, and a mobile setup needs fresh coordinates whenever the vehicle stops at a new site.

Record the exact dish position, intended satellite, contracted frequency, service, installation height and broadcast duration. Build in time for an obstruction survey, a spectrum or access check, and a test transmission. The aim is a repeatable workflow that survives a moved dish, changed line of sight or early start.

Broadcast use What SatPointer should calculate Main field check
Reception Azimuth, elevation and skew toward a receiving satellite Sky view, polarity and signal level
Uplink High-accuracy pointing toward a leased transponder Authorised frequency, bandwidth and uplink limit
Downlink Alignment for a feed returning from a remote site Beam coverage and chosen dish aperture
Mobile Recalculated angles as the vehicle location changes GPS update and safe stopping position

Set the location and pointing requirements

Open the location in SatPointer's map and place the marker on the dish position, not the venue's postal address or centroid. In Melbourne or Sydney, a few hundred metres can alter the view toward a geostationary satellite. Record coordinates, ground level and the bearing to the clear horizon.

Check the sky arc, not one compass direction. Melbourne's towers, Sydney's harbour-side structures and Brisbane's high-rises can create low-angle obstructions. Walk the proposed pad with a compass and receiver where practical. Confirm clearance from parapets, lighting rigs and trees throughout the event window.

An aperture estimate is only a starting point. Use regional dish-size guidance to compare reception coverage by location and service, then ask the provider for required gain and transmit power. Receive and transmit dishes can need very different sizes. Validate the satellite and transponder against the contracted feed.

Set the pointing sheet in true north. Phone compasses often show magnetic north, and the difference across Australia can waste setup time. Have a technician compare the compass with a calibrated true-bearing reference and record the correction. This matters more than a suburb-name typo.

Choose the right satellite link

Name each path on the production diagram: reception, uplink, downlink or mobile link. Specify whether the dish collects a contribution, sends program material, receives a remote feed or tracks a moving unit. This prevents a crew from choosing an uplink satellite merely because its beam looks nearby.

SatPointer combines the installation point with orbital data to calculate azimuth, elevation and dish orientation. Confirm the Google Maps pin sits on the intended side of a building, then compare the result with the provider's commissioning sheet. Coordinate errors matter where the horizon already sits close to the satellite.

Check beam coverage before selecting an aperture, especially outside major cities. Estimated dish-size information helps compare a Perth or Alice Springs site with a coastal location, but does not replace a provider link budget. Confirm band, polarity, feed arrangement, minimum signal level and transmit capability.

Australian broadcaster names can clarify ownership of each stage. The ABC, SBS, Seven, Nine, Network 10 and Foxtel often appear on production paperwork, while a carrier or production house may supply temporary capacity. Confirm who provides the space segment, gateway and IP hand-over; a broadcaster's name does not identify the transponder.

Prepare the site for Australian conditions

Temporary equipment entering Australia needs a clear import plan. Ask the hire company and freight provider about an ATA Carnet or other customs release, especially for serialised broadcast equipment. Australian mains power is 230 V with Type I plugs, so bring correct adapters, surge protection and residual-current protection rather than relying on overseas fittings.

Put weather protection in the original kit list. Brisbane can bring summer storms, Melbourne's cloud and wind require secure covers, and Perth's heat and dust can affect stands and connectors. Use rated covers, secure every mast and cable, and allow time to dry or replace a damp feeder before transmission.

Keep contingency communications independent of the satellite feed. Crew can use an internet status page; general hosting guidance helps compare uptime, support and recovery options. The backup channel should work if venue internet or power fails, and critical media should not rely on consumer file-sharing.

Build a reliable event-day workflow

Plan the call sheet in UTC, then label local starts across Australian operations. Sydney and Melbourne shift between AEST and AEDT, while Perth uses AWST and Alice Springs uses ACST; daylight-saving changes can create an early error. Give every contractor one clock source.

The first control list should establish the site rather than the transmitter:

  • Confirm exact coordinates, access contact, rooftop load limits and parking.
  • Photograph low-angle obstructions and mark dish, power and fibre positions.
  • Test 230 V supply, circuit protection, cable routes and weather covers.
  • Issue radio channels, time-zone details and the revised run sheet.

The second control list should prove that the broadcast path is ready:

  • Load the provider's settings and compare them with the SatPointer angles.
  • Verify polarity, skew, frequency and authorised bandwidth independently.
  • Keep a backup encoder, feed and power path ready to switch.
  • Record signal level, receiver lock and timecode before the program.

Complete alignment, focus and a test transmission before the venue opens. Store the provider's escalation number in a locked mobile phone and the offline run sheet. If a crew member forgets the PIN, resetting a locked phone offers a recovery reference, but no reset should delay an uplink.

Secure the broadcast and connected devices

Confirm frequency coordination and temporary transmission permissions with the ACMA and satellite provider before testing. A contract with an Australian satellite operator may cover space-segment access without replacing local licence requirements. Keep licence references, authorised bandwidth and escalation contacts in the safety file.

Protect the production network with individual logins, multi-factor authentication and separation from guest Wi-Fi. During checks, have IT open a simple web page on a test laptop to confirm public DNS and HTTPS access. Use it only as a harmless external-page test; the live broadcast remains on the approved feed.

Treat the dish as part of the venue's public-safety plan. Check roof loading, wind limits, ballast, trip routes and emergency access with the venue or council, and put cables under protective ramps. A stable signal cannot compensate for an unsecured stand, damaged lead or cable across an audience path.

Activate the plan and communicate it clearly

Turn the calculation into a shared document. Start with the free SatPointer service to obtain the dish angles, then create one page with coordinates, satellite, transponder, azimuth, elevation, skew, signal target, dish size, access notes and a fallback. Print it for the technician and share it with the production desk.

SatPointer also offers a customisable widget for a website, blog or forum, giving visitors an interactive direction view. Add it to the event page with the broadcast schedule and service name. Keep private transponder details, access codes and staff contacts outside the public view.

Run the final rehearsal against the same brief, then issue one version to the dish crew, production team and suppliers. Open SatPointer, select the exact site, enter the contracted parameters, and produce the event-day pointing brief before equipment leaves the depot. Add local contacts and an alternate site, then brief everyone on one start time and contingency plan.