Plan a dual-LNB setup with SatPointer
A dual-LNB setup can put two satellite services on one offset dish without erecting a second mast, provided the orbital positions suit the dish and feed geometry. Plan the pointing directions first, then confirm that the receiver, cabling and LNB frequencies can carry both signals. The free SatPointer web app combines orbital data with a Google Maps location and calculates azimuth, elevation and alignment geometry for each target. Use it to build two records before buying a multifeed bracket.
That matters in Australia, where the eastern states, Tasmania and Western Australia do not share the same practical satellite arc. A pair that suits a Brisbane backyard may be poor near Perth, while a western pair may waste the useful viewing angle on an east-coast installation. This guide covers using SatPointer to plan a dual-LNB setup for receiving two satellites on one dish, with attention to Australian services, local rules and the difference between a workable alignment and one that only appears feasible on paper.
Choose the satellites before the hardware
Choose the satellite services first, not the dish diameter. Record each service, the transponders needed, orbital longitude and whether channels are free-to-air or subscription-based. Optus and Foxtel are familiar Australian options, but a Foxtel subscription normally comes with an authorised set-top box, while Optus channels may use a separate FTA receiver or supplied box. A multifeed solves signal collection; it does not bypass receiver compatibility or channel access.
Next, check how close the targets sit on the orbital arc. Satellites sharing a slot near 112.7°E, such as several Optus spacecraft, are different from services separated by several degrees. SatPointer's example of aligning for NSS 12 shows the same workflow for a non-Australian satellite: enter your own location rather than copying its angles. Select reception mode for this job, not uplink, downlink or mobile-link calculations.
A single-LNB prime-focus dish points at one satellite. On an offset dish, one feed sits away from the centre, allowing nearby directions to reach separate feed horns. Two LNBs on a properly sized multifeed can therefore collect two satellites, but each feed must occupy the right focal position. SatPointer supplies target directions and estimated dish-size information; it cannot confirm that a bracket, mast or receiver will physically accept the arrangement.
Build a location-specific pointing plan
Enter the installation address into the Google Maps location field and confirm the marker on the street or rooftop area. A postcode is useful for a first pass, but an accurate address improves the obstacle check. For a Melbourne terrace or Brisbane suburban block, enter the actual mounting position if possible. Check the satellite database, then create a separate alignment record for each target.
For each record, save the azimuth measured clockwise from true north, the elevation above the horizon, and the dish skew or polarisation angle. Australian installers often talk about a dish facing north for southern-sky satellites, yet the useful aiming point is the calculated beam direction, not the reflector centre. Offset dishes also require the correct relationship between feed position and dish centre. Follow SatPointer's alignment instructions instead of forcing a sat finder to match an approximate bearing.
Repeat the process at the intended dish location rather than a regional centre. Elevation can change across an orbital arc, and local obstructions make a small azimuth error matter. Keep both alignment records side by side and note their separation in degrees. That separation, with the LNB focal distance and bracket design, predicts whether the feeds can coexist better than the dish size printed on the box.
Check coverage and orbital separation
Coverage is the next filter. A satellite can be visible along your horizon yet deliver little usable signal to your address. SatPointer's guide on interpreting beam coverage maps explains why a broad service footprint is not the same as a focused spot beam. Open each satellite's database entry, find the relevant beam and check the exact location. Pay attention to regional and southern-hemisphere limitations rather than assuming a visible arc guarantees reception.
For eastern Australia, neighbours around 112.7°E and 118.8°E are a common starting pair to investigate. Around Perth, Optus 7 near 144.7°E and spacecraft around 156°E need their own coverage and geometry check. Regional towns can sit outside a beam's best section even with a clear view. If either target has a weak footprint, changing LNB brands will not repair it.
Treat the estimated dish size as an indication, then check it against the selected dish's aperture, focal ratio and feed arrangement. Bigger reflectors improve margin, but the multifeed must still position both apertures accurately. Some receivers expect particular intermediate-frequency ranges; a wideband LNB covering roughly 950–2150 MHz is common for Ku-band reception, while a narrower older unit may miss higher-frequency transponders. Record the actual channel frequencies where possible.
Match the dish to the multifeed
A useful multifeed is more than two brackets side by side. Each LNB must point at a different satellite while both feed horns remain parallel to the dish axis, as the offset geometry requires. SatPointer's calculated azimuth and elevation show where each beam should go; the bracket supplier determines where to put the hardware. An 80–90 cm offset dish is a common starting size for a close eastern Australian pair, but not every separation will suit it.
Larger separations demand more feed spacing and make geometry sensitive to installation errors. Higher dish gain helps with imperfect alignment and rain fade, but cannot compensate for a beam that misses the site. Feed-horn diameter, LNB noise figure and receiver sensitivity also affect usable margin. Match the hardware to both targets rather than relying on the app's estimate.
Planning is deterministic, unlike an online mystery-reveal casino game: calculated angles do not randomly become correct. Software cannot diagnose every physical fault either. A bent bracket, loose LNB connector or poorly seated reflector can look like an aiming error on a meter. If the available dish and bracket cannot achieve the calculated directions, separate dishes or a professionally designed multifeed are more sensible than continual adjustment.
Prepare the cable and receiver path
Plan the signal path before the installer arrives. Use quality RG-6 coax, sound F connectors and gentle bends; seal rooftop penetrations against Australian rain and check coastal fittings for corrosion. Follow local grounding and lightning-protection requirements. Existing masts also need a structural check because a heavier multifeed adds wind load. Work near powerlines or unsafe roof access belongs with a suitably qualified installer.
The receiver and switch or combiner arrangement determine how much extra cabling is needed. A dual-output LNB, DiSEqC switch and independent receivers are different arrangements, not interchangeable without checking the equipment. Label each branch at the dish and receiver. During testing, check lock, signal quality and error rate for both satellites rather than relying only on a strength percentage.
Strong Australian sun can make a rooftop alignment screen difficult to read, so shade the phone and charge it before heading out in the arvo. Keep tools away from live mains wiring and obtain building approval where needed; a Sydney balcony mount may need strata consent even with an excellent view. If your club notes include YouTube demonstrations, a transparent thumbnail downloader can help collect clean visual references for the checklist, but verification must happen at the dish.
Compare the options and start safely
Compare the candidates before committing to hardware. Confirm service access, beam coverage, orbital separation, receiver compatibility and mounting space. A pair that looks ideal in azimuth can still fail if the second feed fouls the bracket, the LNB needs another frequency range or the landlord will not approve a roof mount.
Compare these starting points against your own address:
| Option | Australian context | Check before committing |
|---|---|---|
| Optus near 112.7°E and Telstra near 118.8°E | Eastern seaboard starting point | Exact footprints, channel access and physical feed clearance |
| Optus 7 near 144.7°E and a slot around 156°E | Western Australian starting point | Your town's footprint, beam margin and bracket spacing |
| Optus 9 and Optus 10 near 112.7°E | Same-slot service option | Whether one feed already receives every required transponder |
Start with SatPointer now: enter the exact installation location, choose reception and generate a pointing record for each service. Save the results alongside your dish and multifeed measurements, then take them to the supplier or installer for a physical fit check. If spacing or coverage fails, select a supported larger dish or a second dish instead of forcing the setup. Arrange installation and test both feeds independently before connecting the final receiver arrangement.