How to Use SatPointer With a Known Magnetic Anomaly
Using SatPointer to align a dish for a location with a known magnetic anomaly is mainly an exercise in protecting the north reference. SatPointer can calculate where a satellite should be, but it cannot detect iron ore, a steel roof or a nearby transformer pulling a compass several degrees away from magnetic north.
That distinction matters in Australia. Around Port Hedland and Newman in Western Australia’s Pilbara, magnetite-bearing iron ore and mining infrastructure can produce serious local magnetic disturbance. Elsewhere, reinforced concrete, solar equipment, metal railings or the dish mast itself may be enough to send an installer to the wrong side of a true-north line.
Treat the anomaly as a measured correction
Magnetic declination is the angle between true north and magnetic north. A model based on the earth’s regional field supplies an expected value, while a local anomaly is the signed departure from that value. Before aligning anything, establish whether the known figure represents total local declination or an offset from the modelled value.
If the figure is total local declination, record it as (D_{\text{local}}), along with the model value (D_{\text{model}}). If it is an anomaly value, first confirm its sign and units. A magnetic measurement expressed in nanotesla is not an angular correction and should not be entered as degrees; obtain an angular declination or measured compass offset from the survey source.
Pin down the installation point accurately
Open the main SatPointer calculator and enter the installation address through Google Maps, drag the map pin or use the browser’s location function. For a disturbed site, use the surveyed coordinates rather than a property address, since even a small map displacement can alter the calculated azimuth.
Select the appropriate reception, uplink, downlink or mobile satellite link and then the intended satellite. The satellite database can add useful context through beam-coverage information and estimated dish size. A dish that falls just inside the edge of a beam may receive a weaker signal, while an oversized dish cannot fully compensate for pointing in the wrong direction.
Read the pointing result correctly
SatPointer uses orbital data to calculate the satellite’s expected direction. Record the azimuth, elevation and any available skew or feed-rotation value. Most importantly, identify whether the displayed azimuth is referenced to magnetic north or true north; treating the two as interchangeable defeats the purpose of correcting a local anomaly.
The satellite network details can help match a provider’s current satellite entry with the corresponding orbital data. Check the satellite designation, service type and footprint against the receiver or operator information before relying on the result.
The practical distinctions are:
| Pointing value | Reference direction | Use during alignment |
|---|---|---|
| Magnetic azimuth | Modelled magnetic north | Apply the local anomaly correction before transferring it to a compass |
| True azimuth | Geographic true north | Use as the independent reference for checking the magnetic result |
| Local declination | The angle between true and locally observed magnetic north | Use the surveyed value for the exact installation point |
| Elevation | Vertical angle above the horizon | Set with an inclinometer or receiver guidance; a horizontal magnetic anomaly does not change it |
| Feed rotation or skew | Orientation of the dish face and feed assembly | Apply where required by an offset dish or mobile antenna |
Elevation remains unaffected by a horizontal compass anomaly, but skew can still be wrong if the installer aligns from the wrong face of the dish. Photographing the intended satellite position and feed-arm orientation before loosening the bracket helps prevent confusion.
Convert magnetic and true bearings
Use a consistent convention in which east declination is positive and west declination is negative. The local magnetic bearing is:
[ M_{\text{local}} = A_{\text{true}} - D_{\text{local}} ]
If SatPointer provides a magnetic azimuth calculated with the modelled declination, convert it to the local value with:
[ M_{\text{local}} = M_{\text{SatPointer}} + D_{\text{model}} - D_{\text{local}} ]
For example, suppose SatPointer gives a magnetic azimuth of 327° using 12° east modelled declination, while the survey records 18° east locally. The local compass bearing is (327 + 12 - 18 = 321°). The same result comes from subtracting 18° from the corresponding true azimuth of 339°.
Verify this calculation against a reliable true-north mark, a surveyed bearing or another controlled reference. Calibrate the compass outdoors with a figure-eight movement, read it well away from vehicles, steel and electrical equipment, and repeat the observation at the installation. A large discrepancy between two readings is evidence of local interference rather than an error in the satellite calculation.
Prepare the dish and work area
Before heading onto the roof, decide where the compass will be used. A dish mounted directly over a steel bracket can distort the reading at the mounting position, so take the final horizontal bearing several metres away and transfer it to the dish. Fit the cable and secure the mast before fine alignment; otherwise movement of the bracket can introduce errors.
Australian conditions add practical constraints. Sydney and Melbourne terraces may have limited roof access, nearby metalwork and restricted sightlines, while Pilbara installations must cope with heat, dust and salt-laden air. Seals, cable entries and connectors should be suitable for the local environment, and work near power equipment or overhead conductors needs appropriate precautions.
Use these pre-install checks:
- Record the satellite, service type, azimuth, elevation, skew, local declination and anomaly source.
- Check that the mast is plumb, secure and fitted with a reliable bubble level.
- Select a compass-reading location away from metalwork, vehicles, transformers and reinforced edges.
- Calibrate the compass and confirm its reading against a trusted true-north reference.
Use this sequence at the mast:
- Set the mast vertical and establish the approximate elevation.
- Transfer the corrected horizontal bearing to the dish and tighten the bracket.
- Adjust azimuth in small increments while watching the receiver’s signal meter.
- Set feed rotation where applicable, refine elevation and refasten without shifting the mast.
For mobile or L-band equipment, the mobile satellite setup guide explains the additional equipment and alignment considerations that can accompany directional mobile links.
Test the signal and distinguish alignment faults
Begin with a known, accessible transponder rather than relying only on a channel scan. Watch signal strength and quality while making small azimuth and elevation corrections. Once a stable lock is established, check several channels or services carried by the same satellite to confirm that the improvement is repeatable.
If the satellite meter is strong but an internet-delivered channel stalls, do not loosen the dish immediately. Server capacity and media processing are separate from pointing accuracy; this cloud transcoding performance review illustrates the resource demands of a transcoding workflow and why a strong RF signal does not guarantee smooth delivery.
The local market also affects equipment choices. Australian reception businesses commonly service free-to-air, subscription and community television carried by Optus or Telstra satellites. Comparing the chosen beam and required dish diameter before buying components can prevent an installer in Perth, Brisbane or Adelaide from purchasing equipment that is technically suitable but commercially impractical.
Make the result repeatable and share it
Save the final true and corrected magnetic bearings, elevation, skew, signal readings and satellite details. Note the compass used and the distance from the dish at which its reading was taken. This record is valuable if a bracket moves, a new LNB is fitted or another technician later needs to reproduce the alignment.
SatPointer also provides an embeddable widget for websites, blogs and forums. Operators using a Hugo or Jekyll site can consult this simple hosting guide before adding a pointing tool to a regional reception page or installer resource. Start the alignment now by entering the surveyed coordinates in SatPointer, recording the magnetic result and calculating the corrected bearing for the exact site.